Contact Us
If you still have questions or prefer to get help directly from an agent, please submit a request.
We’ll get back to you as soon as possible.
Cole Fuquay
cfuquay@carkeysexpress.com
0
Article
Last Month
2010 Chevrolet Equinox Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
If you have one working keyless fob then you can use these instructions. If you have no working keys to start then you must find an automotive locksmith or dealer to program the new keys with special equipment. Insert the working key into ignition and turn it to on then off and remove. Within 10 seconds insert a new cut key into ignition and turn it
2011 Chevrolet Equinox Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
If you have one working keyless fob then you can use these instructions. If you have no working keys to start then you must find an automotive locksmith or dealer to program the new keys with special equipment. Insert the working key into ignition and turn it to on then off and remove. Within 10 seconds insert a new cut key into ignition and turn it
2012 Chevrolet Equinox Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
If you have one working keyless fob then you can use these instructions. If you have no working keys to start then you must find an automotive locksmith or dealer to program the new keys with special equipment. Insert the working key into ignition and turn it to on then off and remove. Within 10 seconds insert a new cut key into ignition and turn it
Car Keys Express Simple Key: Replacement CDJ Fobik Simple Key - Manual
Published October 27th, 2022 by Cole Fuquay
CDJ FOBIK Simple Key Manual
I am unable to find a key code.
Published November 22nd, 2022 by Cole Fuquay
Use a brush to clean off the key and remove any dirt that may be in crevasses. If no key code is generated by the Gymkana, compare the key cuts to what the Gymkana shows. Manually adjust any of the key cuts that look off on the Gymkana and hit “find key code” to see if a valid key code is found.
2008 Mazda CX-9 Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
NOTE: These instructions are NOT for the smart key system. Open the driver side door and leave it open. Lock and Unlock the driver's door using the power door lock switch on the door Insert the key into the ignition. Turn Key to ON position and return to Lock (off) position. Do this three times within 10 seconds. LEAVE the key in the ignition in
2000 Toyota Sienna Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
2005 Dodge Ram Pickup Truck Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
IMPORTANT NOTE: You must have one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a locksmith or dealership use a programming tool. Enter your vehicle and close all doors. Fasten your seat belt (fastening the seat belt will cancel any chiming t
Can Aftermarket Equipment installed on my vehicle lead to programming issues?
Published January 18th, 2024 by Cole Fuquay
Yes it absolutely can cause issues with programming with this device or any programming device. Aftermarket equipment generally leads to alterations of original equipment installed by the manufacturer and can also lead to alterations in programming in some cases. These combined can lead to issues that you can not predict going into key/remote progra
New key is working, but remote functions are not.
Published November 22nd, 2022 by Cole Fuquay
This can happen for a variety of reasons. The key and chip may not be programmed at the same time as each other. Some will use a separate programming method all together. It could be a program with your device or even an On-board Program method that is needed. After attempting all programming methods you will want to verify the battery in the new r
2004 Chevrolet Monte Carlo Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Turn the ignition to ACC or on and the radio to off. Do not crank the engine. Press and hold the display button on the radio for at least five seconds until settings is displayed. Press the seek up or down arrows until fob program appears on the display. Press the previous or next button to enter the submenu. The current selection will have an aster
2009 Mazda MX-5 Miata Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Instructions for Vehicles without Smart Entry System Remove key from ignition Close all doors Open the driver's door Perform following steps within 24 seconds. Turn ignition switch ON and back to LOCK position three times Close and open driver's door three times Door locks should lock and unlock automatically, if they do not wait 40 seconds
2002 Toyota Sienna Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
2006 Mazda MX-5 Miata Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Instructions for Vehicles without Smart Entry System Remove key from ignition Close all doors Open the driver's door Perform following steps within 24 seconds. Turn ignition switch ON and back to LOCK position three times Close and open driver's door three times Door locks should lock and unlock automatically, if they do not wait 40 seconds
ROKS Box Frequently Asked Questions
Published January 9th, 2024 by Cole Fuquay
How do I know if we have a key/remote for a specific vehicle? The ROKS will tell you. Just input the year, make, and model of the vehicle. My key is not showing up on the device. Is there a way to special order through Car Keys Express? Yes, a sales associate can usually order keys directly from Car Keys Express. Or you can visit our website: www.Ca
2000 Chevrolet Monte Carlo Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Turn the ignition to ACC or on and the radio to off. Do not crank the engine. Press and hold the display button on the radio for at least five seconds until settings is displayed. Press the seek up or down arrows until fob program appears on the display. Press the previous or next button to enter the submenu. The current selection will have an aster
2006 Infiniti FX Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
These Instructions are for vehicles without Smart Entry System/SES NOTE: Withdraw key completely from the ignition cylinder each time. If this procedure is performed too fast, the system will not enter Programming mode. Close and lock all doors with the driver's side power lock/unlock switch. Insert the key into the ignition and remove it from the
1999 Toyota Solara Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
2000 Acura TL Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
1999 Mazda 626 Remote Programming Instructions
Published May 30th, 2025 by Cole Fuquay
Remove the key from the ignition. Close all doors. Open the driver-side door and leave it open. Perform the following steps within 24 seconds. Insert the key in the ignition. Turn the key to ON and OFF. Repeat step 2 two more times. Remove key. Push the driver door frame button three times (the black rubber button located on the driver door frame te
Programming Bible (SmartCircle)
Published November 21st, 2022 by Cole Fuquay
Programming Bible Smartcircle
2000 Mercury Cougar Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Turn the ignition from off to run 4 times within 6 seconds. Turn the ignition off. The system will chime to confirm Programming mode. Within 20 seconds, press any button on the first keyless remote. The system will chime once to confirm Programming. Within 20 seconds, press any button on the second keyless remote. System will chime once to confirm P
2002 Dodge Stratus Coupe Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2005 Cadillac STS Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Programming with a Recognized Remote: To program a new transmitter to your vehicle when you have a recognized remote, do the following. 1. The vehicle must be off. 2. Have the recognized remote and the new, unrecognized remote(s) with you. 3. Insert the vehicle key into the key lock cylinder located on the outside of the driver’s door. 4. Turn
2002 Mazda MPV Vehicles Remote Programming Instructions
Published May 30th, 2025 by Cole Fuquay
Remove the key from the ignition. Close all doors. Open the driver-side door and leave it open. Perform the following steps within 24 seconds. Insert the key in the ignition. Turn the key to ON and OFF. Repeat step 2 two more times. Remove key. Push the driver door frame button three times (the black rubber button located on the driver door frame te
2008 Mazda MX-5 Miata Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Instructions for Vehicles without Smart Entry System Remove key from ignition Close all doors Open the driver's door Perform following steps within 24 seconds. Turn ignition switch ON and back to LOCK position three times Close and open driver's door three times Door locks should lock and unlock automatically, if they do not wait 40 seconds
2002 Mazda 626 Remote Programming Instructions
Published May 30th, 2025 by Cole Fuquay
Remove the key from the ignition. Close all doors. Open the driver-side door and leave it open. Perform the following steps within 24 seconds. Insert the key in the ignition. Turn the key to ON and OFF. Repeat step 2 two more times. Remove key. Push the driver door frame button three times (the black rubber button located on the driver door frame te
"Unable to communicate with Vehicle"
Published December 27th, 2023 by Cole Fuquay
When you get a communication error while attempting to use the programmer there can be multiple reasons that are casuing the issue: The Wi-Fi/Cell Service is not strong enough to carry the data Your Bluetooth connection is not paired correctly. The application needs to be updated The device is not securely placed into the OBDII Port on your vehicle
Common Issue: Subaru Key Cut Codes Tip
Published August 11th, 2025 by Cole Fuquay
Subaru is notoriously difficult to find key codes for, and when you do sometimes the codes do not cut correctly. One useful tip for some keys is to enter the codes as the code depths instead of a code series. Enter them in reverse order for example on the emergency keys like SUB KEY 100. For basic transponder keys enter in the order as they are show
2011 Chevrolet Camaro Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Note: Adding Gm Basic Transponder Keys Must Have A Working Key (Manual Procedure) Insert a master/working key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch the ignition off and remove the key. Quickly insert an UN-paired key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch
2009 Cadillac STS Keyless Entry Smart Key Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Programming with a Recognized Transmitter: To program a new transmitter to your vehicle when you have a recognized transmitter, do the following. 1. The vehicle must be off. 2. Have the recognized transmitter and the new, unrecognized transmitter(s) with you. 3. Insert the vehicle key into the key lock cylinder located on the outside of the driv
2008 Mazda MAZDA3 Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Close all doors, open the driver's door, and key out of ignition. Lock and Unlock the driver's door using the power lock switch on the door panel. Insert the key into the ignition. Turn the key to the ON and OFF position 3 times in 10 seconds. Leave the key in the ignition. Close and open the driver's door 3 times ending with the door in the open po
Car Keys Express Simple Key: Replacement Ford Combo Key (High Security blade) - Manual
Published October 28th, 2022 by Cole Fuquay
Ford Combo Simple Key (High Security) Manual
1998 Mazda 626 Remote Programming Instructions
Published May 30th, 2025 by Cole Fuquay
Remove the key from the ignition. Close all doors. Open the driver-side door and leave it open. Perform the following steps within 24 seconds. Insert the key in the ignition. Turn the key to ON and OFF. Repeat step 2 two more times. Remove key. Push the driver door frame button three times (the black rubber button located on the driver door frame te
1998 Oldsmobile Silhouette Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
2007 Mazda MAZDA3 Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Close all doors, open the driver's door, and key out of ignition. Lock and Unlock the driver's door using the power lock switch on the door panel. Insert the key into the ignition. Turn the key to the ON and OFF position 3 times in 10 seconds. Leave the key in the ignition. Close and open the driver's door 3 times ending with the door in the open po
2005 Acura TSX Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
2004 Mitsubishi Eclipse Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2007 Infiniti G35 Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
These Instructions are for vehicles without Smart Entry System/SES NOTE: Withdraw key completely from the ignition cylinder each time. If this procedure is performed too fast, the system will not enter Programming mode. Close and lock all doors with the driver's side power lock/unlock switch. Insert the key into the ignition and remove it from the
2012 Buick Enclave Vehicle Key Programming Instructions
Published September 28th, 2024 by Cole Fuquay
NOTE: These Programming procedures are only good for USA built vehicles. The first digit of your 17 digit VIN number must start with the number 1 or 4. If your VIN number starts with a 2 or 3 or a letter these procedures WILL NOT WORK. Use the following instructions to program a new (cut) key to the vehicle. (When you have an already programmed/wor
2002 Acura TL Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
2009 Dodge Dakota Remote Key Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Any existing remote/keys not used/reprogrammed during Programming will no longer work. With this procedure you are only Programming the remote portion of the key. Instructions for Remote/Key without Transponder Enter the vehicle, close all doors. Turn the ignition to the run position (as far as you can go without starting the engine). Using
Car Keys Express Simple Key: Replacement Ford Combo Key (Edge Cut Blade) - Manual
Published October 28th, 2022 by Cole Fuquay
Ford Combo Simple Key (Edge Cut) Manual
2012 Mazda MAZDA3 Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Mazda 3 without Smart Entry System Remove key from ignition Close all doors. Open the driver's door. Perform following steps within 24 seconds. Turn ignition switch ON and back to LOCK position three times Close and open driver's door three times Door locks should lock and unlock automatically, if they do not wait 40 seconds and repeat the procedure
2005 Chevrolet Monte Carlo Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Turn the ignition to ACC or on and the radio to off. Do not crank the engine. Press and hold the display button on the radio for at least five seconds until settings is displayed. Press the seek up or down arrows until fob program appears on the display. Press the previous or next button to enter the submenu. The current selection will have an aster
2000 Mitsubishi Diamante Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
Honda Combo Simple Key - Online Setup Guide
Published October 28th, 2022 by Cole Fuquay
Honda Combo Simple Key Online Instructions Guide
2016 Chevrolet Cruze Flip Key Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Programming with ONE Recognized remote key fob NOTE: To program a new key, a key blade must be cut to work in your ignition before you begin. Insert the original, already programmed key in the ignition and turn to the key to the ON/RUN position. Turn the key to LOCK/OFF, and remove the key. Insert the new key to be programmed and turn it to the ON
1998 Honda Civic Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Turn Key to the on position. Push and hold **valet button on the stock radio. Door locks will cycle one time. Press any button on the remote one time within 20 seconds. Door locks will cycle again. To program up to 4 additional remotes repeat step 3 for each additional remote. Turn key off Programming is complete.
2004 Chrysler Town and Country Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have your key cut on the remote by a qualified locksmith or your dealership before attempting these programming instructions. Insert the first working key into the ignition. Turn the ignition to the on position for at least three seconds but no longer than fifteen seconds. Turn the Ignition to the off position and remove the first rem
Basic Terminologies
Published November 28th, 2022 by Cole Fuquay
“Switch Ignition ON” means to turn key on to ACC where everything lights up on the dashboard . (DO not start the ignition/engine) Cars with a key hole on passenger side indicates that the car doesn't take a remote (unless the car is from the early 2000s). Terminal Reset means to disconnect the battery in the car. Disconnect positive and neg
2006 Dodge Dakota Remote Key Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Any existing remote/keys not used/reprogrammed during Programming will no longer work. With this procedure you are only Programming the remote portion of the key. Instructions for Remote/Key without Transponder Enter the vehicle, close all doors. Turn the ignition to the run position (as far as you can go without starting the engine). Using
1999 Toyota 4Runner Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Start with key out of the ignition, the driver’s door is open, all others are closed, and the driver’s door is unlocked. Insert the key into ignition (Do NOT turn) and pull it out. Perform these steps within 40 seconds. Using the power door lock switch on DRIVER’S door, perform 5 LOCK/ UNLOCK cycles starting with lock. Use an even pace and try to go
List of Vehicle Key/Remote Limits
Published November 23rd, 2022 by Cole Fuquay
Nissan Smartkeys: 4 Nissan Combo:5 Nissan Transponder Keys:5 Nissan Flip Keys: 4 Ford Smartkeys: 4 Ford Combo: 4 Ford Transponder Keys: 8 CDJ FOBIK: 8 CDJ Smartkeys: 8 CDJ Combo: 8 CDJ Transponder Keys: 8 Toyota Combo Keys: 4 Toyota Transponder Keys: 5 Master, 3 Valet Honda Combo: 3-6 GM Remote: 4 remotes
2000 Toyota 4Runner Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Start with key out of the ignition, the driver’s door is open, all others are closed, and the driver’s door is unlocked. Insert the key into ignition (Do NOT turn) and pull it out. Perform these steps within 40 seconds. Using the power door lock switch on DRIVER’S door, perform 5 LOCK/ UNLOCK cycles starting with lock. Use an even pace and try to go
2007 Acura TSX Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
2001 Chrysler Sebring Two Door Coupe Key Programming Instructions
Published December 27th, 2023 by Cole Fuquay
NOTE: You must have two valid keys to add a new key to the system. If you do not have 2 valid working keys you will have to call a Locksmith to program or originate a key for you. Insert the first valid key into the ignition switch. Turn the ignition switch to the ON position for 5 seconds. Turn the ignition switch to the OFF position and remove t
2002 Dodge Ram Pickup Truck Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
IMPORTANT NOTE: You must have one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a locksmith or dealership use a programming tool. Enter your vehicle and close all doors. Fasten your seat belt (fastening the seat belt will cancel any chiming t
Locating the OBD Port for use with the programmer
Published January 12th, 2024 by Cole Fuquay
The OBD (On board diagnostic) port is generally located under the steering wheel column. There are a few vehicles where it is located on the passenger side glove box area as well. Generally, it is placed well underneath the column so it does not get hit or kicked by accident. There are some vehicles that will locate it behind a small door or cubb
1996 Mitsubishi Eclipse Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
SmartBox Mini - Programming Honda/Acura Transponder Key (Video)
Published June 28th, 2024 by Cole Fuquay
Your browser does not support HTML5 video.
2016 Chevrolet Equinox Remote Key Fob Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Programming with ONE Recognized remote key fob NOTE: To program a new key, a key blade must be cut to work in your ignition before you begin. Insert the original, already programmed key in the ignition and turn to the key to the ON/RUN position. Turn the key to LOCK/OFF, and remove the key. Insert the new key to be programmed and turn it to the ON
Nissan & Infiniti - Tips & Tricks
Published November 28th, 2022 by Cole Fuquay
Infiniti/Nissan Keys – Smart pro will pull old pin and new pin, try old pin first, if that doesn't work, then try new pin. If no pin is pulled, try to start the car with a new key. The car most likely does not need a chip key in this case. Combo key : always program remote first before cutting, follow smart pro. Smart Key: MAKE SURE TO TAKE OUT THE
Nissan Smart Key Series II Simple Key - Troubleshooting Steps
Published October 27th, 2022 by Cole Fuquay
Nissan Smart Key Series II Simple Key Troubleshooting Form Note: For vehicles without a pairing slot.
2008 Mazda CX-7 Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
NOTE: These instructions are NOT for the smart key system. Open the driver side door and leave it open. Lock and Unlock the driver's door using the power door lock switch on the door Insert the key into the ignition. Turn Key to ON position and return to Lock (off) position. Do this three times within 10 seconds. LEAVE the key in the ignition in
2003 Dodge Stratus Coupe Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2000 Ford Focus Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Turn the ignition from off to run 4 times within 6 seconds. Turn the ignition off. The system will chime to confirm Programming mode. Within 20 seconds, press any button on the first keyless remote. The system will chime once to confirm Programming. Within 20 seconds, press any button on the second keyless remote. System will chime once to confirm P
2011 Cadillac STS Keyless Entry Smartkey Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Programming with a Recognized Remote: To program a new transmitter to your vehicle when you have a recognized remote, do the following. 1. The vehicle must be off. 2. Have the recognized remote and the new, unrecognized remote(s) with you. 3. Insert the vehicle key into the key lock cylinder located on the outside of the driver’s door. 4. Turn
2001 Toyota Solara Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
2001 Mazda MPV Vehicles Remote Programming Instructions
Published May 30th, 2025 by Cole Fuquay
Remove the key from the ignition. Close all doors. Open the driver-side door and leave it open. Perform the following steps within 24 seconds. Insert the key in the ignition. Turn the key to ON and OFF. Repeat step 2 two more times. Remove key. Push the driver door frame button three times (the black rubber button located on the driver door frame te
2000 Chevrolet Impala Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Turn the ignition to ACC or on and the radio to off. Do not crank the engine. Press and hold the display button on the radio for at least five seconds until settings is displayed. Press the seek up or down arrows until fob program appears on the display. Press the previous or next button to enter the submenu. The current selection will have an aster
2006 Buick LaCrosse Vehicle Key Programming Instructions
Published December 31st, 2024 by Cole Fuquay
NOTE: These Programming procedures are only good for USA built vehicles. The first digit of your 17 digit VIN number must start with the number 1 or 4. If your VIN number starts with a 2 or 3 or a letter these procedures WILL NOT WORK. Use the following instructions to program a new (cut) key to the vehicle. (When you have an already programmed/wor
2000 Toyota Solara Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
2006 Chrysler Town and Country Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have your key cut on the remote by a qualified locksmith or your dealership before attempting these programming instructions. Insert the first working key into the ignition. Turn the ignition to the on position for at least three seconds but no longer than fifteen seconds. Turn the Ignition to the off position and remove the first rem
2006 Cadillac STS Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Programming with a Recognized Transmitter: To program a new transmitter to your vehicle when you have a recognized transmitter, do the following. 1. The vehicle must be off. 2. Have the recognized transmitter and the new, unrecognized transmitter(s) with you. 3. Insert the vehicle key into the key lock cylinder located on the outside of the driv
2010 Mazda MAZDA3 Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Mazda 3 without Smart Entry System Remove key from ignition Close all doors. Open the driver's door. Perform following steps within 24 seconds. Turn ignition switch ON and back to LOCK position three times Close and open driver's door three times Door locks should lock and unlock automatically, if they do not wait 40 seconds and repeat the procedure
1998 Acura TL Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
2000 Pontiac Montana Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
2004 Honda Pilot Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Entering programming mode erases all remotes that were programmed. You must reprogram all remotes you want to work once you have entered the programming mode. You must perform each of the first twelve steps within 5 seconds of each other to enter programming mode. programming each remote (step 13) must be done within 10 seconds. The system wil
2003 Oldsmobile Silhouette Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
Chevrolet, Buick, GMC, Cadillac, Saturn, & Pontiac - Tips & Tricks
Published November 28th, 2022 by Cole Fuquay
GM (Chevy, Cadillac, GMC, Buick, Saturn, Pontiac) Do NOT use smart pro for smart keys and transponder keys. ONLY use the smart pro for separate remotes. Up to 2016 models – transponder keys – Use the original key first, turn it on and wait till immobilizer light goes away, put new key in and wait till immobilizer light goes away. Remove the key,
2000 Mazda MPV Vehicles Remote Programming Instructions
Published May 30th, 2025 by Cole Fuquay
Remove the key from the ignition. Close all doors. Open the driver-side door and leave it open. Perform the following steps within 24 seconds. Insert the key in the ignition. Turn the key to ON and OFF. Repeat step 2 two more times. Remove key. Push the driver door frame button three times (the black rubber button located on the driver door frame te
2016 Chevrolet Sonic Remote Key Fob Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Programming with ONE Recognized remote key fob NOTE: To program a new key, a key blade must be cut to work in your ignition before you begin. Insert the original, already programmed key in the ignition and turn to the key to the ON/RUN position. Turn the key to LOCK/OFF, and remove the key. Insert the new key to be programmed and turn it to the ON
2004 Toyota Sequoia Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Start with key out of the ignition, the driver’s door is open, all others are closed, and the driver’s door is unlocked. Insert the key into ignition (Do NOT turn) and pull it out. Perform these steps within 40 seconds. Using the power door lock switch on DRIVER’S door, perform 5 LOCK/ UNLOCK cycles starting with lock. Use an even pace and try to go
2008 Acura MDX Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Each step must be completed within 5 seconds. NOTE: All the doors and rear hatch/trunk must be closed during programming. Have the remote for the vehicle on hand. Sit in the car with all doors/trunk tightly closed. Turn the key to the on position, marked by (II) on the ignition bezel so the dash lights come on. Listen for a quiet click, and
2002 Mazda Millenia Remote Programming Instructions
Published May 30th, 2025 by Cole Fuquay
Remove the key from the ignition. Close all doors. Open the driver-side door and leave it open. Perform the following steps within 24 seconds. Insert the key in the ignition. Turn the key to ON and OFF. Repeat step 2 two more times. Remove key. Push the driver door frame button three times (the black rubber button located on the driver door frame te
CDJ Smart Key Simple Key - Troubleshooting Form
Published October 28th, 2022 by Cole Fuquay
CDJ Smart Key Simple Key Troubleshooting Form
1997 Mitsubishi 3000GT Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
Nissan Smart Key EZ Installer PRO Manual
Published July 14th, 2023 by Cole Fuquay
Nissan Smart Key EZ Installer PRO Manual
1999 Oldsmobile Silhouette Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
2002 Ford Focus Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Turn the ignition from off to run 4 times within 6 seconds. Turn the ignition off. The system will chime to confirm Programming mode. Within 20 seconds, press any button on the first keyless remote. The system will chime once to confirm Programming. Within 20 seconds, press any button on the second keyless remote. System will chime once to confirm P
1999 Toyota Sienna Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
Universal Car Remote - Manual
Published October 27th, 2022 by Cole Fuquay
Universal Car Remote Manual
Lexus - Tips & Tricks
Published November 28th, 2022 by Cole Fuquay
Lexus Combo Key – program remote first, check programyourremote.com to program manually/On-board Program. Transponder Blade Keys – Most can be programmed without being cut. Use the smart pro to program keys, combo keys and smart keys. Early 2000s require manual procedures/On-board Programming (Pedal Dance). Smart Key – Put original key against push
2006 Mitsubishi Eclipse Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2005 Mitsubishi Endeavor Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2000 Ford Ranger Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have two (2) functioning and programmed keys in order to program an additional key. If you do not have two (2) existing programmed keys, call an automotive locksmith for a replacement. Insert an existing working key into the ignition Turn the ignition cylinder to ON (RUN) and back to OFF Remove the existing working key and, within fiv
1996 Pontiac Bonneville Remote Programming Instructions
Published September 29th, 2025 by Cole Fuquay
Close all doors. Insert keys in ignition and leave in the off position. Locate the OBDII port under driver's side dashboard. Note port is wider at top: your OBDII port will not have numbers. Use this for reference: Make sure there are metal contact pins in terminals 8 and 4. connect 8 and 4 with a suitable jumper wire (leave jumper wire connected th
2004 Audi A4 Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Insert key into ignition (not valet key). Turn key to "on" position, but do not start engine. Roll down front window on driver's side. Insert second key into door. Turn clockwise to lock all doors, then hold the key in that position. Press "unlock" on the first fob to be programed. Hold for 2 seconds, and the vehicle lights will flash once. Wait 2 s
1999 Mercury Cougar Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Turn the ignition from off to run 4 times within 6 seconds. Turn the ignition off. The system will chime to confirm Programming mode. Within 20 seconds, press any button on the first keyless remote. The system will chime once to confirm Programming. Within 20 seconds, press any button on the second keyless remote. System will chime once to confirm P
2011 Ford Fusion Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: This procedure is for Programming conventional key fobs only. The Remote Keyless Entry (RKE) remote of the integrated Keyhead remote is programed automatically during the Passive Anti-Theft System (PATS) Programming. All RKE remotes must be programmed at the same time. Do not apply the brake pedal during this sequencing, as doing so ends the
2005 Acura TL Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
Ford - Tips & Tricks
Published November 28th, 2022 by Cole Fuquay
Ford Program remote – turn ignition on 8 times, after the 8th the locks with cycle. Press any button on all available remotes. I ncluding the old remote(s) . C ERT For Key Combos keys remote programs with the key (no need to cycle 8 times for cert keys.) High security blades ( FOR 031, 041 combos) Recommend closing all the doors. Cycle on to off 4
2005 Chrysler Town and Country Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have your key cut on the remote by a qualified locksmith or your dealership before attempting these programming instructions. Insert the first working key into the ignition. Turn the ignition to the on position for at least three seconds but no longer than fifteen seconds. Turn the Ignition to the off position and remove the first rem
1998 Pontiac Montana Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
2014 Chevrolet Equinox Remote Key Fob Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Programming with ONE Recognized remote key fob NOTE: To program a new key, a key blade must be cut to work in your ignition before you begin. Insert the original, already programmed key in the ignition and turn to the key to the ON/RUN position. Turn the key to LOCK/OFF, and remove the key. Insert the new key to be programmed and turn it to the ON
Hyundai & Kia - Tips & Tricks
Published November 28th, 2022 by Cole Fuquay
Hyundai/Kia You do not need to program most keys, only remotes. (Only cars that have transponder systems need key programming. Also Canadian built cars come with a transponder key. Recommended to clone these keys) Remotes : Go To System Types ( memorize these and it will take you 30 seconds to program the remote) Remote type 1: 2008 - 2012 Remote t
2015 Chevrolet Equinox Remote Key Fob Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Programming with ONE Recognized remote key fob NOTE: To program a new key, a key blade must be cut to work in your ignition before you begin. Insert the original, already programmed key in the ignition and turn to the key to the ON/RUN position. Turn the key to LOCK/OFF, and remove the key. Insert the new key to be programmed and turn it to the ON
2014 Buick Enclave Key Programming Instructions
Published December 31st, 2024 by Cole Fuquay
NOTE: These Programming procedures are only good for USA built vehicles. The first digit of your 17 digit VIN number must start with the number 1 or 4. If your VIN number starts with a 2 or 3 or a letter these procedures WILL NOT WORK. Use the following instructions to program a new (cut) key to the vehicle. (When you have an already programmed/wor
2003 Toyota Sequoia Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Start with key out of the ignition, the driver’s door is open, all others are closed, and the driver’s door is unlocked. Insert the key into ignition (Do NOT turn) and pull it out. Perform these steps within 40 seconds. Using the power door lock switch on DRIVER’S door, perform 5 LOCK/ UNLOCK cycles starting with lock. Use an even pace and try to go
2012 Ford Fusion Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: This procedure is for Programming conventional key fobs only. The Remote Keyless Entry (RKE) remote of the integrated Keyhead remote is programed automatically during the Passive Anti-Theft System (PATS) Programming. All RKE remotes must be programmed at the same time. Do not apply the brake pedal during this sequencing, as doing so ends the
2005 Dodge Durango Remote Key Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Any existing remote/keys not used/reprogrammed during Programming will no longer work. With this procedure you are only Programming the remote portion of the key. Instructions for Remote/Key without Transponder Enter the vehicle, close all doors. Turn the ignition to the run position (as far as you can go without starting the engine). Using
Subaru - Tips & Tricks
Published November 28th, 2022 by Cole Fuquay
Subaru Combo key – program the remote first, you will need the 8 digit code (if there is no code label, the code is likely inside of the remote) after entering the code - press lock and unlock until it starts working. Transponder Key – Use the smart pro ( some models erase all the keys so you have to program both, test both keys to make sure they s
2017 Chevrolet Equinox Remote Key Fob Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Programming with ONE Recognized remote key fob NOTE: To program a new key, a key blade must be cut to work in your ignition before you begin. Insert the original, already programmed key in the ignition and turn to the key to the ON/RUN position. Turn the key to LOCK/OFF, and remove the key. Insert the new key to be programmed and turn it to the ON
2001 Toyota Avalon Transponder Key Programming
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
2007 Acura MDX Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Each step must be completed within 5 seconds. NOTE: All the doors and rear hatch/trunk must be closed during programming. Have the remote for the vehicle on hand. Sit in the car with all doors/trunk tightly closed. Turn the key to the on position, marked by (II) on the ignition bezel so the dash lights come on. Listen for a quiet click, and
2006 Acura TSX Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
Chrysler, Dodge, & Jeep - Tips & Tricks
Published November 28th, 2022 by Cole Fuquay
CDJ (Chrysler, Jeep, Dodge) Pull the pin code on all CDJ vehicles with smart pro. (we can't pull pin code on any combos keys on 05-07 Jeep liberty, Town and Country, Caravan, Grand Caravan and Pacifica) CDJ key 500 require a brass key CDJ key 201 M to pull a pin code (send it back as “other” in notes put “used to pull pin code”) Program Immobilizer:
2005 Mitsubishi Eclipse Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2003 Acura TL Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
2010 Buick Enclave Vehicle Key Programming Instructions
Published September 28th, 2024 by Cole Fuquay
NOTE: These Programming procedures are only good for USA built vehicles. The first digit of your 17 digit VIN number must start with the number 1 or 4. If your VIN number starts with a 2 or 3 or a letter these procedures WILL NOT WORK. Use the following instructions to program a new (cut) key to the vehicle. (When you have an already programmed/wor
Mitsubishi - Tips & Tricks
Published November 28th, 2022 by Cole Fuquay
Mitsubishi Transponder K eys – Program the remote first then use smart pro for the key. Remote – These need Breakout Box – Close door, plug in breakout box, put key in ignition, connect to terminal 1 and 4, within 10 seconds, press hazard light button 6 times, car will cycle, press unlock twice on each remote. Smart keys – Follow smart pro procedur
2003 Chevrolet Monte Carlo Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Turn the ignition to ACC or on and the radio to off. Do not crank the engine. Press and hold the display button on the radio for at least five seconds until settings is displayed. Press the seek up or down arrows until fob program appears on the display. Press the previous or next button to enter the submenu. The current selection will have an aster
Common Issue: SmartPro Cable Intermittently Working
Published December 5th, 2022 by Cole Fuquay
Some times the SmartPro main OBD connection cable can go bad from every day use and usual wear and tear. Signs the cable is bad: - It will only work on certain vehicle makes. - Vehicle voltage shows 0. - Visible Physical Damage - Attempted to update device, device recovery, & device full reset and issues continue.
General Motors Remote with EZ Installer: GMPRR-7000
Published July 14th, 2023 by Cole Fuquay
General Motors Remote with EZ Installer Manual (2006 - 2017 Select Models)
2001 Mazda Millenia Remote Programming Instructions
Published May 30th, 2025 by Cole Fuquay
Remove the key from the ignition. Close all doors. Open the driver-side door and leave it open. Perform the following steps within 24 seconds. Insert the key in the ignition. Turn the key to ON and OFF. Repeat step 2 two more times. Remove key. Push the driver door frame button three times (the black rubber button located on the driver door frame te
Car Keys Express Replacement Remote (FOR 060) - Manual
Published October 25th, 2022 by Cole Fuquay
FOR 060 Manual .
2001 Dodge Stratus Coupe Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2013 Chevrolet Camaro Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Note: Adding Gm Basic Transponder Keys Must Have A Working Key (Manual Procedure) Insert a master/working key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch the ignition off and remove the key. Quickly insert an UN-paired key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch
1995 Chevrolet CK-Series Truck Remote Programming Instructions
Published March 20th, 2024 by Cole Fuquay
Locate the Data Link Connector (DLC) underneath the driver's side dashboard. Use the figure as a map for your DL ( They are not lettered on your vehicle.) Connect cavity G to a ground. Your vehicle will respond by locking and unlocking the door locks within 2 seconds. Press the lock or unlock button on the first remote to be programmed. Locks will
1996 Honda Civic Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Valet button is a skinny bar located between AM/FM & cd/tape buttons on stock radio. Turn Key to the on position. Push and hold **valet button on the stock radio. Door locks will cycle one time. Press any button on the remote one time within 20 seconds. Door locks will cycle again. To program up to 4 additional remotes repeat step 3 for ea
2001 Toyota Camry Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
2008 Acura TSX Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
Car Keys Express Simple Key: Replacement Nissan Smart Key Series I (programming slot) - Manual
Published October 27th, 2022 by Cole Fuquay
Nissan Smart Key Series I Simple Key Manual
Volkswagen - Tips & Tricks
Published November 29th, 2022 by Cole Fuquay
Volkswagen programmable up to 2014 with key in the ignition only Remote - Follow Smart Pro procedure Keys - Follow Smart Pro procedure. If it asks for a pin use Xhorse to clone the chip. Most of the time you can clone the chip that is already inside of the key. If it is not cloning use an Xhorse chip.
2003 Toyota Solara Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
2005 Infiniti FX Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
These Instructions are for vehicles without Smart Entry System/SES NOTE: Withdraw key completely from the ignition cylinder each time. If this procedure is performed too fast, the system will not enter Programming mode. Close and lock all doors with the driver's side power lock/unlock switch. Insert the key into the ignition and remove it from the
2005 Dodge Stratus Coupe Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
Car Keys Express Replacement Remote (TOY 044) - Manual
Published October 27th, 2022 by Cole Fuquay
TOY 044 Manual
2001 Chevrolet Impala Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Turn the ignition to ACC or on and the radio to off. Do not crank the engine. Press and hold the display button on the radio for at least five seconds until settings is displayed. Press the seek up or down arrows until fob program appears on the display. Press the previous or next button to enter the submenu. The current selection will have an aster
CDJ 505 & 555 Smartkeys Confusion
Published July 24th, 2024 by Cole Fuquay
CDJ 505 SMARTKEY & CDJ 555 SMARTKEY . While both of these SKUs are compatible with the 2024 Jeep Grand Cherokee, they are NOT cross compatible. If you are servicing a 2024 Grand Cherokee, you must match the FCCID on your key with the customer's key. Using the incorrect key can cause problems with the vehicle.
1995 Chevrolet Suburban Remote Programming Instructions
Published March 20th, 2024 by Cole Fuquay
Locate the Data Link Connector (DLC) underneath the driver's side dashboard. Use the figure as a map for your DL ( They are not lettered on your vehicle.) Connect cavity G to a ground. Your vehicle will respond by locking and unlocking the door locks within 2 seconds. Press the lock or unlock button on the first remote to be programmed. Locks will
2009 Acura MDX Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Each step must be completed within 5 seconds. NOTE: All the doors and rear hatch/trunk must be closed during programming. Have the remote for the vehicle on hand. Sit in the car with all doors/trunk tightly closed. Turn the key to the on position, marked by (II) on the ignition bezel so the dash lights come on. Listen for a quiet click, and
2004 Mitsubishi Diamante Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2005 Ford Focus Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Turn the ignition from off to run 4 times within 6 seconds. Turn the ignition off. The system will chime to confirm Programming mode. Within 20 seconds, press any button on the first keyless remote. The system will chime once to confirm Programming. Within 20 seconds, press any button on the second keyless remote. System will chime once to confirm P
2003 Mitsubishi Diamante Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2002 Toyota 4Runner Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Start with key out of the ignition, the driver’s door is open, all others are closed, and the driver’s door is unlocked. Insert the key into ignition (Do NOT turn) and pull it out. Perform these steps within 40 seconds. Using the power door lock switch on DRIVER’S door, perform 5 LOCK/ UNLOCK cycles starting with lock. Use an even pace and try to go
2002 Mitsubishi Eclipse Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
1999 Mitsubishi Diamante Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2004 Oldsmobile Silhouette Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
Car Keys Express Simple Key: Replacement Nissan Smart Key Series II - Manual
Published October 27th, 2022 by Cole Fuquay
Nissan Smart Key Series II Simple Key Manual
Mazda - Tips & Tricks
Published November 28th, 2022 by Cole Fuquay
Mazda Mazda Key – Use smart pro to add keys. Remotes - Mazda remotes program manually most of the time (switch ignition on to off 3 times then close open door 3 times) Mazda smart key – program the remote first, then follow smart pro for adding a key procedure. 2017 and up must wait 10 minutes to bypass security.
2007 Dodge Dakota Remote Key Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Any existing remote/keys not used/reprogrammed during Programming will no longer work. With this procedure you are only Programming the remote portion of the key. Instructions for Remote/Key without Transponder Enter the vehicle, close all doors. Turn the ignition to the run position (as far as you can go without starting the engine). Using
2007 Chrysler Town and Country Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have your key cut on the remote by a qualified locksmith or your dealership before attempting these programming instructions. Insert the first working key into the ignition. Turn the ignition to the on position for at least three seconds but no longer than fifteen seconds. Turn the Ignition to the off position and remove the first rem
2005 Chevrolet Impala Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Turn the ignition to ACC or on and the radio to off. Do not crank the engine. Press and hold the display button on the radio for at least five seconds until settings is displayed. Press the seek up or down arrows until fob program appears on the display. Press the previous or next button to enter the submenu. The current selection will have an aster
2003 Mazda MPV Remote Programming Instructions
Published June 3rd, 2025 by Cole Fuquay
Remove the key from the ignition. Close all doors. Open the driver-side door and leave it open. Perform the following steps within 24 seconds. Insert the key in the ignition. Turn the key to ON and OFF. Repeat step 2 two more times. Remove key. Push the driver door frame button three times (the black rubber button located on the driver door frame te
2003 Dodge Ram Pickup Truck Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
IMPORTANT NOTE: You must have one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a locksmith or dealership use a programming tool. Enter your vehicle and close all doors. Fasten your seat belt (fastening the seat belt will cancel any chiming t
Nissan Transponder Key Classic
Published July 14th, 2023 by Cole Fuquay
Nissan Transponder Simple Key Classic Manual
1999 Acura TL Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
1996 Mitsubishi 3000GT Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
1996 Mitsubishi Eclipse Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
Car Keys Express Replacement Remote (NIS 060) - Manual
Published October 27th, 2022 by Cole Fuquay
NIS 060 Manual
2002 Chrysler Sebring Two Door Coupe Key Programming Instructions
Published December 27th, 2023 by Cole Fuquay
NOTE: You must have two valid keys to add a new key to the system. If you do not have 2 valid working keys you will have to call a Locksmith to program or originate a key for you. Insert the first valid key into the ignition switch. Turn the ignition switch to the ON position for 5 seconds. Turn the ignition switch to the OFF position and remove t
2006 Mitsubishi Endeavor Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2004 Mitsubishi Endeavor Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2002 Mercury Cougar Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Turn the ignition from off to run 4 times within 6 seconds. Turn the ignition off. The system will chime to confirm Programming mode. Within 20 seconds, press any button on the first keyless remote. The system will chime once to confirm Programming. Within 20 seconds, press any button on the second keyless remote. System will chime once to confirm P
2005 Mazda MAZDA3 Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Close all doors, open the driver's door, and key out of ignition. Lock and Unlock the driver's door using the power lock switch on the door panel. Insert the key into the ignition. Turn the key to the ON and OFF position 3 times in 10 seconds. Leave the key in the ignition. Close and open the driver's door 3 times ending with the door in the open po
CDJ Fobik Simple Key - Troubleshooting Steps
Published October 27th, 2022 by Cole Fuquay
CDJ Fobik Simple Key Troubleshooting Form
2016 Chevrolet Camaro Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Note: Adding Gm Basic Transponder Keys Must Have A Working Key (Manual Procedure) Insert a master/working key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch the ignition off and remove the key. Quickly insert an UN-paired key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch
1995 Chevrolet Tahoe Remote Programming Instructions
Published March 12th, 2024 by Cole Fuquay
Locate the Data Link Connector (DLC) underneath the driver's side dashboard. Use the figure as a map for your DL ( They are not lettered on your vehicle.) Connect cavity G to a ground. Your vehicle will respond by locking and unlocking the door locks within 2 seconds. Press the lock or unlock button on the first remote to be programmed. Locks will
1998 Chevrolet Venture Van Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
2001 Toyota 4Runner Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
1997 Honda Civic Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Turn Key to the on position. Push and hold **valet button on the stock radio. Door locks will cycle one time. Press any button on the remote one time within 20 seconds. Door locks will cycle again. To program up to 4 additional remotes repeat step 3 for each additional remote. Turn key off Programming is complete.
Nissan Smart Key Series I (programming slot) Simple Key - Troubleshooting Steps
Published October 27th, 2022 by Cole Fuquay
Nissan Smart Key Series I Simple Key Troubleshooting Form Note: For Vehicles with a pairing slot.
2007 Toyota Sequoia Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Start with key out of the ignition, the driver’s door is open, all others are closed, and the driver’s door is unlocked. Insert the key into ignition (Do NOT turn) and pull it out. Perform these steps within 40 seconds. Using the power door lock switch on DRIVER’S door, perform 5 LOCK/ UNLOCK cycles starting with lock. Use an even pace and try to go
2010 Cadillac STS Keyless Entry Smart Key Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Programming with a Recognized Transmitter: To program a new transmitter to your vehicle when you have a recognized transmitter, do the following. 1. The vehicle must be off. 2. Have the recognized transmitter and the new, unrecognized transmitter(s) with you. 3. Insert the vehicle key into the key lock cylinder located on the outside of the driv
2004 Acura TL Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
2010 Chevrolet Traverse Remote Programming Instructions
Published December 27th, 2023 by Cole Fuquay
NOTE: This vehicle can have a maximum of eight remotes programmed. Using the Drivers Information Center Section: Insert the key and turn to on position so you can access the Driver Information Center. Press the vehicle information button until "Press to relearn remote key" is displayed. Press the set/reset button until "Remote key learning active"
2003 Ford Focus Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Turn the ignition from off to run 4 times within 6 seconds. Turn the ignition off. The system will chime to confirm Programming mode. Within 20 seconds, press any button on the first keyless remote. The system will chime once to confirm Programming. Within 20 seconds, press any button on the second keyless remote. System will chime once to confirm P
Car Keys Express Replacement Remote (GM 660) OEM - Manual
Published October 25th, 2022 by Cole Fuquay
GM 660 OEM Manual
2004 Chevrolet Impala Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Turn the ignition to ACC or on and the radio to off. Do not crank the engine. Press and hold the display button on the radio for at least five seconds until settings is displayed. Press the seek up or down arrows until fob program appears on the display. Press the previous or next button to enter the submenu. The current selection will have an aster
2010 Camaro Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Note: Adding Gm Basic Transponder Keys Must Have A Working Key (Manual Procedure) Insert a master/working key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch the ignition off and remove the key. Quickly insert an UN-paired key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch
1998 Toyota Avalon Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
Car Keys Express Simple Key: Replacement GM Flip Key - Manual
Published October 28th, 2022 by Cole Fuquay
GM Flip Simple Key Manual
1999 Toyota Avalon Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
2001 Ford Focus Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Turn the ignition from off to run 4 times within 6 seconds. Turn the ignition off. The system will chime to confirm Programming mode. Within 20 seconds, press any button on the first keyless remote. The system will chime once to confirm Programming. Within 20 seconds, press any button on the second keyless remote. System will chime once to confirm P
Toyota Combo Simple Key - Troubleshooting Form
Published October 28th, 2022 by Cole Fuquay
Toyota Combo Simple Key Troubleshooting Form
2015 Chevrolet Sonic Remote Key Fob Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Programming with ONE Recognized remote key fob NOTE: To program a new key, a key blade must be cut to work in your ignition before you begin. Insert the original, already programmed key in the ignition and turn to the key to the ON/RUN position. Turn the key to LOCK/OFF, and remove the key. Insert the new key to be programmed and turn it to the ON
2000 Mazda 626 Remote Programming Instructions
Published May 30th, 2025 by Cole Fuquay
Remove the key from the ignition. Close all doors. Open the driver-side door and leave it open. Perform the following steps within 24 seconds. Insert the key in the ignition. Turn the key to ON and OFF. Repeat step 2 two more times. Remove key. Push the driver door frame button three times (the black rubber button located on the driver door frame te
2002 Toyota Solara Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
Ford Combo Simple Key - Troubleshooting Steps
Published October 28th, 2022 by Cole Fuquay
Ford Combo Simple Key Troubleshooting Form
2003 Toyota Sienna Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
2002 Toyota Sequoia Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Start with key out of the ignition, the driver’s door is open, all others are closed, and the driver’s door is unlocked. Insert the key into ignition (Do NOT turn) and pull it out. Perform these steps within 40 seconds. Using the power door lock switch on DRIVER’S door, perform 5 LOCK/ UNLOCK cycles starting with lock. Use an even pace and try to go
1999 Mitsubishi Eclipse Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2008 Mazda MAZDA6 Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Close all doors, open the driver's door, and key out of ignition. Lock and Unlock the driver's door using the power lock switch on the door panel. Insert the key into the ignition. Turn the key to the ON and OFF position 3 times in 10 seconds. Leave the key in the ignition. Close and open the driver's door 3 times ending with the door in the open po
Does my key need to be cut before using this device?
Published January 12th, 2024 by Cole Fuquay
Yes, any new bladed key for a turn key ignition must be cut before using this device. During the process you will need to be able to turn the ignition to the ON position for most vehicles. The key must be cut to turn the ignition and complete the proper programming process.
Car Keys Express Simple Key: Replacement CDJ Smart Key - Manual
Published October 28th, 2022 by Cole Fuquay
CDJ Smart Key Simple Key Manual
2006 Acura TL Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
1999 Ford Ranger Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have two (2) functioning and programmed keys in order to program an additional key. If you do not have two (2) existing programmed keys, call an automotive locksmith for a replacement. Insert an existing working key into the ignition Turn the ignition cylinder to ON (RUN) and back to OFF Remove the existing working key and, within fiv
2003 BMW 3-Series Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Working from within the vehicle and with the doors shut Turn ignition to position 1 and back to off within 5 seconds. Remove the key from ignition and press and hold the unlock button for 15 seconds during this time press the key lock button 3 times within 5 seconds. Release both buttons. Doors will lock and unlock to show correct programming has oc
2014 Chevrolet Cruze Flip Key Programming Instructions
Published May 13th, 2024 by Cole Fuquay
Programming with ONE Recognized remote key fob NOTE: To program a new key, a key blade must be cut to work in your ignition before you begin. Insert the original, already programmed key in the ignition and turn to the key to the ON/RUN position. Turn the key to LOCK/OFF, and remove the key. Insert the new key to be programmed and turn it to the ON
2000 Toyota Camry Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
Car Keys Express Replacement Remote (SUB 062) - Manual
Published October 27th, 2022 by Cole Fuquay
SUB 062 Manual
READ Before Programming 2017-2019 Cadillac ATS
Published June 4th, 2024 by Cole Fuquay
When programming a key to a 2017-2019 Cadillac ATS, always pop the trunk BEFORE pulling the PIN code. The battery is located in the trunk and is very difficult to access if the vehicle is locked up. The only way to access the battery if the vehicle is locked up is to unbolt and remove the back seat.
Is this device compatible with OBD 1 ports?
Published January 12th, 2024 by Cole Fuquay
No currently this device is not compatible with an OBD1 Port on older vehicles. OBD2 has been the standard for vehicle manufactures for years now and is currently the only OBD port we support with this device.
2007 Infiniti FX Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
These Instructions are for vehicles without Smart Entry System/SES NOTE: Withdraw key completely from the ignition cylinder each time. If this procedure is performed too fast, the system will not enter Programming mode. Close and lock all doors with the driver's side power lock/unlock switch. Insert the key into the ignition and remove it from the
2012 Chevrolet Camaro Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Note: Adding Gm Basic Transponder Keys Must Have A Working Key (Manual Procedure) Insert a master/working key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch the ignition off and remove the key. Quickly insert an UN-paired key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch
Universal Car Remote Classic - Manual
Published October 28th, 2022 by Cole Fuquay
Universal Car Remote Classic Manual
2002 Chevrolet Monte Carlo Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Turn the ignition to ACC or on and the radio to off. Do not crank the engine. Press and hold the display button on the radio for at least five seconds until settings is displayed. Press the seek up or down arrows until fob program appears on the display. Press the previous or next button to enter the submenu. The current selection will have an aster
2011 Buick Enclave Vehicle Key Programming Instructions
Published September 28th, 2024 by Cole Fuquay
NOTE: These Programming procedures are only good for USA built vehicles. The first digit of your 17 digit VIN number must start with the number 1 or 4. If your VIN number starts with a 2 or 3 or a letter these procedures WILL NOT WORK. Use the following instructions to program a new (cut) key to the vehicle. (When you have an already programmed/wor
2002 Oldsmobile Silhouette Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
2004 Mazda MAZDA6 Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Open the driver's door and leave it open. Lock and Unlock the driver's door using the power lock switch on the door panel. Insert the key into the ignition. Turn the key to the ON and OFF position three times in 10 seconds. Leave the key in the ignition. Open and close the driver's door three times ending with the door in the open position. Door loc
Car Keys Express Simple Key: Replacement Hondo Combo Key - Manual
Published October 27th, 2022 by Cole Fuquay
Honda Combo Simple Key Manual
2000 Oldsmobile Silhouette Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
Does the Universal EZ Installer work on vehicles built outside the United States?
Published January 18th, 2024 by Cole Fuquay
No this programmer is not designed to work with any vehicle not originally built for operation in the United States. This includes vehicles that have been shipped overseas from the United States. There are too many variables and changes that are small, but have to be made to vehicles being driven in countries other than the United States to meet app
2008 Dodge Dakota Remote Key Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Any existing remote/keys not used/reprogrammed during Programming will no longer work. With this procedure you are only Programming the remote portion of the key. Instructions for Remote/Key without Transponder Enter the vehicle, close all doors. Turn the ignition to the run position (as far as you can go without starting the engine). Using
1998 Mitsubishi Eclipse Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
Car Keys Express Replacement Remote (NIS 055) - Manual
Published October 27th, 2022 by Cole Fuquay
NIS 055 Manual
ROKS Box Quick-Start Guide
Published January 9th, 2024 by Cole Fuquay
Step 1. Remove your ROKS Box and power cable from the packaging. Plug the power cable into the nearest wall outlet. Step 2. Connect your ROKS Box. Thread the power cable into the power connection at the back of the box. Step 3. After connecting the power, do not touch the screen for 30-60 seconds. This is intended to allow the ROKS Box to find a dat
"Communication Error" on Programmer
Published November 22nd, 2022 by Cole Fuquay
This can be caused by the vehicle, programmer, key, or user. If the vehicle has a damaged OBDII port it will not be able to communicate with the programming device or if the vehicle's battery is too low of a voltage. If the programmer is damaged or needs an update it may not be able to communicate with the vehicle. If the key is bad and is not gett
2007 Buick LaCrosse Vehicle Key Programming Instructions
Published December 31st, 2024 by Cole Fuquay
NOTE: These Programming procedures are only good for USA built vehicles. The first digit of your 17 digit VIN number must start with the number 1 or 4. If your VIN number starts with a 2 or 3 or a letter these procedures WILL NOT WORK. Use the following instructions to program a new (cut) key to the vehicle. (When you have an already programmed/wor
2007 Cadillac STS Keyless Entry Smart Key Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Programming with a Recognized Transmitter: To program a new transmitter to your vehicle when you have a recognized transmitter, do the following. 1. The vehicle must be off. 2. Have the recognized transmitter and the new, unrecognized transmitter(s) with you. 3. Insert the vehicle key into the key lock cylinder located on the outside of the driv
2002 Mitsubishi Diamante Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2008 Buick Enclave Vehicle Key Programming Instructions
Published September 28th, 2024 by Cole Fuquay
NOTE: These Programming procedures are only good for USA built vehicles. The first digit of your 17 digit VIN number must start with the number 1 or 4. If your VIN number starts with a 2 or 3 or a letter these procedures WILL NOT WORK. Use the following instructions to program a new (cut) key to the vehicle. (When you have an already programmed/wor
2003 Infiniti FX Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
These Instructions are for vehicles without Smart Entry System/SES NOTE: Withdraw key completely from the ignition cylinder each time. If this procedure is performed too fast, the system will not enter Programming mode. Close and lock all doors with the driver's side power lock/unlock switch. Insert the key into the ignition and remove it from the
"Communication Error"
Published January 10th, 2024 by Cole Fuquay
Although uncommon there are times when using the Universal EZ Installer you may encounter a communication error. Listed below are common causes of the error and what to verify to fix the concern. Device is not plugged in to the OBD port fully The Bluetooth is not paired between phone and device The wi-fi connection is not stable or strong enough Th
1997 Pontiac Bonneville Remote Programming Instructions
Published September 29th, 2025 by Cole Fuquay
Close all doors. Insert keys in ignition and leave in the off position. Locate the OBDII port under driver's side dashboard. Note port is wider at top: your OBDII port will not have numbers. Use this for reference: Make sure there are metal contact pins in terminals 8 and 4. connect 8 and 4 with a suitable jumper wire (leave jumper wire connected th
2000 Chevrolet Venture Van Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
How many keys can I program to my car?
Published January 12th, 2024 by Cole Fuquay
Every vehicle has a limit to how many keys it can hold in its memory. There is no standard or set amount and it varies by make, model, and year of the vehicle. The best source of information to find out how many keys your vehicle can hold is your owners manual. If you do not have this you can contact a local dealership and provide your make, model,
2005 Dodge Dakota Remote Key Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Any existing remote/keys not used/reprogrammed during Programming will no longer work. With this procedure you are only Programming the remote portion of the key. Instructions for Remote/Key without Transponder Enter the vehicle, close all doors. Turn the ignition to the run position (as far as you can go without starting the engine). Using
2009 Chevrolet Traverse Remote Programming Instructions
Published December 27th, 2023 by Cole Fuquay
NOTE: This vehicle can have a maximum of eight remotes programmed. Using the Drivers Information Center Section: Insert the key and turn to on position so you can access the Driver Information Center. Press the vehicle information button until "Press to relearn remote key" is displayed. Press the set/reset button until "Remote key learning active"
2014 Chevrolet Sonic Remote Key Fob Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Programming with ONE Recognized remote key fob NOTE: To program a new key, a key blade must be cut to work in your ignition before you begin. Insert the original, already programmed key in the ignition and turn to the key to the ON/RUN position. Turn the key to LOCK/OFF, and remove the key. Insert the new key to be programmed and turn it to the ON
Car Keys Express Simple Key: Replacement Toyota Combo Key - Manual
Published October 28th, 2022 by Cole Fuquay
Toyota Combo Simple Key Manual
2001 Chevrolet Monte Carlo Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Turn the ignition to ACC or on and the radio to off. Do not crank the engine. Press and hold the display button on the radio for at least five seconds until settings is displayed. Press the seek up or down arrows until fob program appears on the display. Press the previous or next button to enter the submenu. The current selection will have an aster
2004 Mazda MAZDA3 Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Close all doors, open the driver's door, and key out of ignition. Lock and Unlock the driver's door using the power lock switch on the door panel. Insert the key into the ignition. Turn the key to the ON and OFF position 3 times in 10 seconds. Leave the key in the ignition. Close and open the driver's door 3 times ending with the door in the open po
"VIN Decode Error"
Published December 27th, 2023 by Cole Fuquay
There will be times that the programmer is unable to recognize or pull a vehicle's VIN. If you get the “VIN Decode Error” it means this. You will want to verify the year, make, and model of the vehicle. Then manually enter the year, make, and model skipping past inputting the VIN. This will provide you with the proper programming instructions for y
Do I need a working key to use this device?
Published January 11th, 2024 by Cole Fuquay
Yes. All vehicles that this programmer is compatible with will require a 100% functional key that currently starts the vehicle. The programming process will generally need it for: Copy over information from the original key Require it for security access on the vehicles system.
2008 Cadillac STS Keyless Entry Smart Key Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Programming with a Recognized Transmitter: To program a new transmitter to your vehicle when you have a recognized transmitter, do the following. 1. The vehicle must be off. 2. Have the recognized transmitter and the new, unrecognized transmitter(s) with you. 3. Insert the vehicle key into the key lock cylinder located on the outside of the driv
1999 Chevrolet Venture Van Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
Ford Transponder Key Classic
Published July 14th, 2023 by Cole Fuquay
Ford Transponder Key Simple Key Classic Manual
Nissan Combo Key EZ Installer PRO Manual
Published July 14th, 2023 by Cole Fuquay
Nissan Combo Key EZ Installer PRO Manual
2006 Toyota RAV4 Remote Programming Instructions
Published January 9th, 2024 by Cole Fuquay
NOTE: These instructions will only program the remote portion of your key/remote combo. You will need to get the key blade cut, and if you have a transponder chip in your key, it will need to be programmed by a locksmith. 1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked. 2. Perform these
2001 Mercury Cougar Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Turn the ignition from off to run 4 times within 6 seconds. Turn the ignition off. The system will chime to confirm Programming mode. Within 20 seconds, press any button on the first keyless remote. The system will chime once to confirm Programming. Within 20 seconds, press any button on the second keyless remote. System will chime once to confirm P
2004 Chrysler Sebring 2DR Coupe Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2004 Ford Focus Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Turn the ignition from off to run 4 times within 6 seconds. Turn the ignition off. The system will chime to confirm Programming mode. Within 20 seconds, press any button on the first keyless remote. The system will chime once to confirm Programming. Within 20 seconds, press any button on the second keyless remote. System will chime once to confirm P
Car Keys Express Replacement Remote (HON 042) - Manual
Published October 27th, 2022 by Cole Fuquay
HON 042 Manual
1997 Mitsubishi Eclipse Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2001 Oldsmobile Silhouette Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
2004 Dodge Durango Remote Key Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Any existing remote/keys not used/reprogrammed during Programming will no longer work. With this procedure you are only Programming the remote portion of the key. Instructions for Remote/Key without Transponder Enter the vehicle, close all doors. Turn the ignition to the run position (as far as you can go without starting the engine). Using
Toyota Transponder Key Classic
Published July 14th, 2023 by Cole Fuquay
Toyota Transponder Key Simple Key Classic Manual
2003 Mitsubishi Eclipse Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
Car Keys Express Simple Key: Replacement Nissan Combo Key - Manual
Published October 18th, 2022 by Cole Fuquay
Nissan Combo Simple Key Manual
1995 Mitsubishi Expo Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
1999 Pontiac Montana Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Remove key from ignition. Remove the "BCM PRGRM" fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the "BCMPRGRM" fuse. Close all of the doors. Close the liftgate. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you -- the opposite
ROKS Box Maintenance Instructions
Published January 9th, 2024 by Cole Fuquay
Screen Cleaning/Touchscreen Handling This device is often located near or adjacent to an automotive or mechanical shop. These locations may generate substances (automotive grease, cleaners, oil, etc) that can degrade the touch screen functionality of the device over time. Additionally, regular use will cause oil/dirt to build up on the screen from c
2003 Mazda MAZDA6 Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Open the driver's door and leave it open. Lock and Unlock the driver's door using the power lock switch on the door panel. Insert the key into the ignition. Turn the key to the ON and OFF position three times in 10 seconds. Leave the key in the ignition. Open and close the driver's door three times ending with the door in the open position. Door loc
1998 Mitsubishi 3000GT Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2001 Mazda 626 Remote Programming Instructions
Published May 30th, 2025 by Cole Fuquay
Remove the key from the ignition. Close all doors. Open the driver-side door and leave it open. Perform the following steps within 24 seconds. Insert the key in the ignition. Turn the key to ON and OFF. Repeat step 2 two more times. Remove key. Push the driver door frame button three times (the black rubber button located on the driver door frame te
2001 Mitsubishi Eclipse Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2001 Toyota Sienna Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
2006 Toyota Sequoia Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Start with key out of the ignition, the driver’s door is open, all others are closed, and the driver’s door is unlocked. Insert the key into ignition (Do NOT turn) and pull it out. Perform these steps within 40 seconds. Using the power door lock switch on DRIVER’S door, perform 5 LOCK/ UNLOCK cycles starting with lock. Use an even pace and try to go
2000 Mitsubishi Eclipse Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
What do you do when the ROKS Box application is not showing on the device?
Published March 28th, 2024 by Cole Fuquay
Complete a hard restart. Open the panel on the side of the box and hold the power button down on the tablet device for 3-5 seconds. The user can then choose an option to either restart or turn off the device. Either option will work, if the user turns it off they will have to manually turn it back on. If your device does not open you may have a ne
2015 Chevrolet Camaro Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Note: Adding Gm Basic Transponder Keys Must Have A Working Key (Manual Procedure) Insert a master/working key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch the ignition off and remove the key. Quickly insert an UN-paired key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch
2013 Buick Enclave Vehicle Key Programming Instructions
Published December 31st, 2024 by Cole Fuquay
NOTE: These Programming procedures are only good for USA built vehicles. The first digit of your 17 digit VIN number must start with the number 1 or 4. If your VIN number starts with a 2 or 3 or a letter these procedures WILL NOT WORK. Use the following instructions to program a new (cut) key to the vehicle. (When you have an already programmed/wor
2009 Buick LaCrosse Vehicle Key Programming Instructions
Published December 31st, 2024 by Cole Fuquay
NOTE: These Programming procedures are only good for USA built vehicles. The first digit of your 17 digit VIN number must start with the number 1 or 4. If your VIN number starts with a 2 or 3 or a letter these procedures WILL NOT WORK. Use the following instructions to program a new (cut) key to the vehicle. (When you have an already programmed/wor
2006 Mazda MAZDA3 Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Close all doors, open the driver's door, and key out of ignition. Lock and Unlock the driver's door using the power lock switch on the door panel. Insert the key into the ignition. Turn the key to the ON and OFF position 3 times in 10 seconds. Leave the key in the ignition. Close and open the driver's door 3 times ending with the door in the open po
2015 Chevrolet Cruze Remote Key Fob Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Programming with ONE Recognized remote key fob NOTE: To program a new key, a key blade must be cut to work in your ignition before you begin. Insert the original, already programmed key in the ignition and turn to the key to the ON/RUN position. Turn the key to LOCK/OFF, and remove the key. Insert the new key to be programmed and turn it to the ON
2002 Chevrolet Impala Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Turn the ignition to ACC or on and the radio to off. Do not crank the engine. Press and hold the display button on the radio for at least five seconds until settings is displayed. Press the seek up or down arrows until fob program appears on the display. Press the previous or next button to enter the submenu. The current selection will have an aster
2005 Mazda MAZDA6 Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Open the driver's door and leave it open. Lock and Unlock the driver's door using the power lock switch on the door panel. Insert the key into the ignition. Turn the key to the ON and OFF position three times in 10 seconds. Leave the key in the ignition. Open and close the driver's door three times ending with the door in the open position. Door loc
2010 Ford Fusion Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: This procedure is for Programming conventional key fobs only. The Remote Keyless Entry (RKE) remote of the integrated Keyhead remote is programed automatically during the Passive Anti-Theft System (PATS) Programming. All RKE remotes must be programmed at the same time. Do not apply the brake pedal during this sequencing, as doing so ends the
Car Keys Express Replacement Remote (GM 840) - Manual
Published October 27th, 2022 by Cole Fuquay
GM 840 Manual
1996 Mitsubishi Expo Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2014 Chevrolet Camaro Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Note: Adding Gm Basic Transponder Keys Must Have A Working Key (Manual Procedure) Insert a master/working key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch the ignition off and remove the key. Quickly insert an UN-paired key and switch the ignition on. Wait for the security/immobilizer light to go out. Switch
General Motors Transponder Key Classic
Published July 14th, 2023 by Cole Fuquay
General Motors Transponder Simple Key Classic Manual
Car Keys Express Replacement Remote (HON 025) - Manual
Published October 27th, 2022 by Cole Fuquay
HON 025 Manual
2017 Chevrolet Sonic Remote Key Fob Programming Instructions
Published June 24th, 2024 by Cole Fuquay
Programming with ONE Recognized remote key fob NOTE: To program a new key, a key blade must be cut to work in your ignition before you begin. Insert the original, already programmed key in the ignition and turn to the key to the ON/RUN position. Turn the key to LOCK/OFF, and remove the key. Insert the new key to be programmed and turn it to the ON
2004 Infiniti FX Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
These Instructions are for vehicles without Smart Entry System/SES NOTE: Withdraw key completely from the ignition cylinder each time. If this procedure is performed too fast, the system will not enter Programming mode. Close and lock all doors with the driver's side power lock/unlock switch. Insert the key into the ignition and remove it from the
2009 Buick Enclave Vehicle Key Programming Instructions
Published September 28th, 2024 by Cole Fuquay
NOTE: These Programming procedures are only good for USA built vehicles. The first digit of your 17 digit VIN number must start with the number 1 or 4. If your VIN number starts with a 2 or 3 or a letter these procedures WILL NOT WORK. Use the following instructions to program a new (cut) key to the vehicle. (When you have an already programmed/wor
Toyota - Tips & Tricks
Published November 29th, 2022 by Cole Fuquay
Toyota Remotes – If the vehicle is older than 2006, it will most likely be manual procedure/on board programming, other remotes, all programs under remote type 4. Except FJ Cruiser. Key – There are 3 types of keys - memorize these and it will help you to cut down on time to program these keys. (if the customer has a gray key (valet key) we cann
2005 Audi A4 Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
IMPORTANT NOTE: You will need one working remote and a key. Have the driver's door closed and the window open. Turn key in the ignition to on. Turn a second key in the door to lock Push the unlock button on the door once for each remote to be programed. Turn the ignition to off. Remove keys from the door and the ignition. Do not open the door. On re
2000 Toyota Avalon Transponder Key Programming Instructions
Published March 28th, 2024 by Cole Fuquay
NOTE: You must have a working master key for this procedure. Insert the master Toyota already programmed key into the ignition. Press and release the accelerator pedal 5 times within 15 seconds of inserting the key into the ignition. Press and release the brake pedal 6 times within 20 seconds of step 2. Remove the black key from the ignition switch.
2008 Buick LaCrosse Vehicle Key Programming Instructions
Published December 31st, 2024 by Cole Fuquay
NOTE: These Programming procedures are only good for USA built vehicles. The first digit of your 17 digit VIN number must start with the number 1 or 4. If your VIN number starts with a 2 or 3 or a letter these procedures WILL NOT WORK. Use the following instructions to program a new (cut) key to the vehicle. (When you have an already programmed/wor
2004 Dodge Ram Pickup Truck Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
IMPORTANT NOTE: You must have one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a locksmith or dealership use a programming tool. Enter your vehicle and close all doors. Fasten your seat belt (fastening the seat belt will cancel any chiming t
2005 Buick LaCrosse Vehicle Key Programming Instructions
Published December 31st, 2024 by Cole Fuquay
NOTE: These Programming procedures are only good for USA built vehicles. The first digit of your 17 digit VIN number must start with the number 1 or 4. If your VIN number starts with a 2 or 3 or a letter these procedures WILL NOT WORK. Use the following instructions to program a new (cut) key to the vehicle. (When you have an already programmed/wor
2007 Mazda MX-5 Miata Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Instructions for Vehicles without Smart Entry System Remove key from ignition Close all doors Open the driver's door Perform following steps within 24 seconds. Turn ignition switch ON and back to LOCK position three times Close and open driver's door three times Door locks should lock and unlock automatically, if they do not wait 40 seconds
2006 Ford Focus Remote Programming Instructions
Published March 28th, 2024 by Cole Fuquay
Turn the ignition from off to run 4 times within 6 seconds. Turn the ignition off. The system will chime to confirm Programming mode. Within 20 seconds, press any button on the first keyless remote. The system will chime once to confirm Programming. Within 20 seconds, press any button on the second keyless remote. System will chime once to confirm P
2005 Honda Pilot Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Entering programming mode erases all remotes that were programmed. You must reprogram all remotes you want to work once you have entered the programming mode. You must perform each of the first twelve steps within 5 seconds of each other to enter programming mode. programming each remote (step 13) must be done within 10 seconds. The system wil
2003 Chevrolet Impala Remote Programming Instructions
Published June 25th, 2024 by Cole Fuquay
Turn the ignition to ACC or on and the radio to off. Do not crank the engine. Press and hold the display button on the radio for at least five seconds until settings is displayed. Press the seek up or down arrows until fob program appears on the display. Press the previous or next button to enter the submenu. The current selection will have an aster
2005 Toyota Sequoia Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Start with key out of the ignition, the driver’s door is open, all others are closed, and the driver’s door is unlocked. Insert the key into ignition (Do NOT turn) and pull it out. Perform these steps within 40 seconds. Using the power door lock switch on DRIVER’S door, perform 5 LOCK/ UNLOCK cycles starting with lock. Use an even pace and try to go
2006 Infiniti G35 Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
These Instructions are for vehicles without Smart Entry System/SES NOTE: Withdraw key completely from the ignition cylinder each time. If this procedure is performed too fast, the system will not enter Programming mode. Close and lock all doors with the driver's side power lock/unlock switch. Insert the key into the ignition and remove it from the
Car Keys Express Replacement Remote (GM 790) - Manual
Published October 27th, 2022 by Cole Fuquay
GM 790 Manual
2005 Infiniti G35 Remote Programming Instructions
Published June 24th, 2024 by Cole Fuquay
These Instructions are for vehicles without Smart Entry System/SES NOTE: Withdraw key completely from the ignition cylinder each time. If this procedure is performed too fast, the system will not enter Programming mode. Close and lock all doors with the driver's side power lock/unlock switch. Insert the key into the ignition and remove it from the
1999 Mitsubishi 3000GT Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
Acura & Honda - Tips & Tricks
Published November 28th, 2022 by Cole Fuquay
Acura/Honda Program remote first before cutting To program remote: Turn ignition, press unlock on remote, turn ignition off. Repeat this 4X, car locks will cycle, then press any button on all remotes, including original. Exceptions: Combo keys that remote programs with the key: HON 040. 045, 056, 057.5, 058, 058.5, 060, 070, 071, 072, 072.5 comb
2001 Acura TL Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
NOTE: Entering the programming mode cancels all programmed keyless entry remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. Turn ig
2009 Mazda CX-9 Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
NOTE: These instructions are NOT for the smart key system. Open the driver side door and leave it open. Lock and Unlock the driver's door using the power door lock switch on the door Insert the key into the ignition. Turn Key to ON position and return to Lock (off) position. Do this three times within 10 seconds. LEAVE the key in the ignition in
2001 Mitsubishi Diamante Remote Programming Instructions
Published March 27th, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2004 Dodge Stratus Coupe Remote Programming Instructions
Published March 21st, 2024 by Cole Fuquay
Locate the Data Port/OBD2 Port. (Most commonly located on driver's side under steering column) Insert the key into the ignition and leave in the off position. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Port with a suitable jumper wire, leave jumper wire connected throughout the programming procedure. Make sure y
2006 Dodge Durango Remote Key Programming Instructions
Published June 24th, 2024 by Cole Fuquay
NOTE: Any existing remote/keys not used/reprogrammed during Programming will no longer work. With this procedure you are only Programming the remote portion of the key. Instructions for Remote/Key without Transponder Enter the vehicle, close all doors. Turn the ignition to the run position (as far as you can go without starting the engine). Using
2011 Mazda MAZDA3 Remote Programming Instructions
Published June 26th, 2024 by Cole Fuquay
Mazda 3 without Smart Entry System Remove key from ignition Close all doors. Open the driver's door. Perform following steps within 24 seconds. Turn ignition switch ON and back to LOCK position three times Close and open driver's door three times Door locks should lock and unlock automatically, if they do not wait 40 seconds and repeat the procedure
Load More